DR PREMIER RAPIDFIRE Instruções de Operação

Read and understand this manual and all instructions before operating the DR PREMIER RAPIDFIRE LOG SPLITTER. Original Language DR® PREMIER RAPIDFIRE

10 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Installing the Log Table Kit Parts Supplied (Figure 6): Item # Part # Description Qty 1 ...

CONTACT US AT www.DRpower.com 11 5. Install the Tray Bracket to the Frame Stand with four Carriage Bolts and Locknuts using two 9/16" W

12 DR® PREMIER RAPIDFIRE™ LOG SPLITTER 6. Remove the Gas Fill Cap and fill the Gas Tank with fresh, unleaded gas (with a minimum of 85 Octane

CONTACT US AT www.DRpower.com 13 Operator Zone Figure 15 TOP VIEW Chapter 3: Operating The DR PREMIER RAPIDFIRE LOG SPLITTER It may be helpfu

14 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Electric Motor Model Starting the Motor 1. Position your Log Splitter on flat, dry ground and chock th

CONTACT US AT www.DRpower.com 15 Figure 21 Wood Against Wedge Hands on Sides of Wood 1. Place the log on the Log Splitter. Grasp the log on

16 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Chapter 4: Maintaining The DR PREMIER RAPIDFIRE LOG SPLITTER Regular maintenance is the way to ensure t

CONTACT US AT www.DRpower.com 17 3. Remove the four short Flange Bolts and Locknuts that secure the right side Guard to the Frame using a 9/

18 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Greasing the Rack It is important to grease the Rack every 5 hours for proper operation. Tools and Supp

CONTACT US AT www.DRpower.com 19 Note: The weight of the Engine should be enough to tension the Belts properly but depending on hardware loo

2 DR® PREMIER RAPIDFIRE™ LOG SPLITTER This indicates a hazardous situation, which, if not avoided, could result in death or serious injury. Ta

20 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Adjusting the Steel Bushing Over Center Tools needed:  Two 9/16" Wrenches  9/16" Socket a

CONTACT US AT www.DRpower.com 21 The Handle Yoke must move just past center as it contacts the Bolt Stop. If it is at the center position, o

22 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Chapter 5: Troubleshooting Most problems are easy to fix. Consult the Troubleshooting Table below for c

CONTACT US AT www.DRpower.com 23 Troubleshooting Table (Continued) SYMPTOM POSSIBLE CAUSE The Motor does not run  Splitter unplugged; plug

24 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Chapter 6: Parts Lists and Schematic Diagrams Parts List – FRAME STAND AND GUARD ASSEMBLY NOTE: Part nu

CONTACT US AT www.DRpower.com 25 Schematic – FRAME STAND AND GUARD ASSEMBLY

26 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Parts List – DRIVE ASSEMBLY NOTE: Part numbers listed are available through DR Power Equipment. Ref# Pa

CONTACT US AT www.DRpower.com 27 Schematic – DRIVE ASSEMBLY

28 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Parts List – FRAME AND AXLE ASSEMBLY NOTE: Part numbers listed are available through DR Power Equipment

CONTACT US AT www.DRpower.com 29 Schematic – FRAME AND AXLE ASSEMBLY

CONTACT US AT www.DRpower.com 3 Read this Safety & Operating Instructions manual before you use the DR RAPIDFIRE LOG SPLITTER. Become fa

30 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Parts List – TRAY KIT ASSEMBLY NOTE: Part numbers listed are available through DR Power Equipment. Ref#

CONTACT US AT www.DRpower.com 31 Notes:

75 MEIGS ROAD, P.O. BOX 25, VERGENNES, VERMONT 05491 ©2014 Country Home Products, Inc. All rights reserved 351721 Daily Checklist for the DR PREMIER

4 DR® PREMIER RAPIDFIRE™ LOG SPLITTER This is a high-powered machine, with moving parts operating with high energy. You must operate the mach

CONTACT US AT www.DRpower.com 5 Never overlook the hazards of electricity. Always follow these precautions:  Never open the switch box or

6 DR® PREMIER RAPIDFIRE™ LOG SPLITTER General Safety A Note to All Users Under California law, and the laws of some other states, you are not

CONTACT US AT www.DRpower.com 7 Figure 1 Chapter 2: Setting Up The DR PREMIER RAPIDFIRE LOG SPLITTER It may be helpful to familiarize yoursel

8 DR® PREMIER RAPIDFIRE™ LOG SPLITTER Specifications GAS ENGINE ELECTRIC MOTOR HP 3 0.5 Output Torque 3.5 ft-lbs (4.7 N-m) 1.47 ft-lbs (2 N-

CONTACT US AT www.DRpower.com 9 1. Support the Beam with a Jack Stand or equivalent so the front of the Beam is high enough to install the F